Integrated Cart: $875

The sleek design blends the cart with a VersaLaser™ for a stylish floor standing unit.

• Maximum stability at low cost
• Durable construction for many years of dependable service
• Locking casters for moving convenience
• Two large storage drawers
• Top indents "lock" VersaLaser™ unit in place

      Click here for additional information

Size:
25" W x 22" D x 30" H
(635mm x 559mm x 762mm)

Weight:
95 lbs. (43.1 kg)

Computer Controlled Air Cleaner / Cart: $2715

The same sleek design and function as the Integrated Cart except storage space is replaced by built in air cleaner.

• Controlled through a USB port and activated only when jobs are in process
• Air cleaner is concealed behind drawers (no storage)
• Air filtration eliminates smoke and dust

      Click here for additional information

Size:
25"W x 27"D x 30"H
(635mm x 686mm x 762mm)

Weight:
160 lbs. (72.6 kg) without filters (shipped with one set of filters); 170 lbs. (77 kg) with filters installed

Recommended for installations where venting to the outside is not convenient or possible.

Replacement Filters

Pre-filter: $18

• Captures dust and large particles

HEPA Filter: $150

• Captures smoke

Carbon Filter: $390

• Removes odor

Rotary Fixture:
(VLS2.30 - $850, VLS3.50 - $900)

Allows a VersaLaser™ to be quickly reconfigured to engrave and cut cylindrical objects.

• Allows maximum part diameter of up to 5.0 inches (127mm)
• Loading and unloading is quick and easy
• An easy to use software interface provides for quick and precise layout on any material
• Hot swappable for convenience
• A sensor detects the presence of rotary fixture when it's installed and adjusts automatically

      Click here for additional information

For VLS2.30

Size:
18.8" W x 4.8" D x 5.3" H
(478mm x 122mm x 135mm)
Weight:
9 lbs. (4.1 kg)

For VLS3.50

Size:
26.8” W x 4.8” D x 5.3” H
(681mm x 122mm x 135mm)
Weight:
10 lbs. (4.5kg)

Downdraft Cutting Table
(VLS2.30 - $240, VLS3.50 - $340)

A simple yet functional design provides support and light vacuum hold down for sheet stock while allowing smoke and debris from the cutting process to be removed.

• Honeycomb cutting surface supports material with a minimum of contact area
• Hot swappable for convenience
• A sensor detects the presence of cutting table when it's installed and automatically adjusts the Z-axis automatically to place materials at the proper focus

      Click here for additional information

Recommended for cutting thin materials that tend to curl or cutting materials where visual cut quality is important on both front and back of cut material.

For VLS2.30

Size:
18.8" W x 14.5" D x 4.5" H
(478mm x 368mm x 114mm)
Weight:
3 lbs. (1.4 kg)

For VLS3.50

Size:
26.8” W x 14.5” D x 4.5” H
(681mm x 368mm x 114mm)
Weight:
4 lbs. (1.8kg)

High Power Density Focusing Optics: $2,650

Allows engraving of smaller text, higher resolution graphics and photographs and vector marking and cutting of thinner lines.

• Engrave smaller text
• Vector mark and cut thinner lines
• Mark uncoated metals, like stainless steel, without using metal marking compounds

Computer Controlled Compressed Air Unit: $1,290

Supplies dry oil-free compressed air to protect optics and enable air assisted cutting and engraving

• Controlled through a USB port and is activated only when jobs are in process
• The compressor pump is noise insulated for quiet operation
• An air dryer is integrated into the unit to remove optics damaging water

Size:
14.2"W x 11.1"D x 18"H
(361mm x 282mm x 457mm)

Weight:
44 lbs. (20 Kg)

Recommended for any cutting operation or engraving operation that creates dust or smoke to protect optics.

Must purchase Refrigerated Dryer Kit ($1,290) or Desiccant Dryer Kit ($430) separately

Air Assist Back Sweep: $225

Recommended for use with the Computer Controlled Compressed Air Unit, the Back Sweep attachment directs air toward the exhaust duct . This is important for rubber engraving or engraving of other materials that produce a lot of dust during the engraving process

Air Assist Cone: $140

Recommended for use with the Computer Controlled Compressed Air Unit, the cone directs air onto material being cut or engraved and improves cutting or engraving quality of most materials.

Lens Kit (1.5” 2.0") $328
(2.0" lens included with each VersaLaser)

Protected and manufactured under one or more of U.S. Patents 5,661,746; 5,754,575; 5,867,517; 5,881,087; 5,894,493; 5,901,167; 5,982,803; 6,181,719;6,313,433; 6,342,687; 6,423,925; 6,424,670. Other U.S. and International patents pending.

Prices are in U.S. Dollars, and do not include taxes, duties, freight or special packaging charges. Standard shipping packaging is included. Prices and specifications are subject to change without notice.